You walk to make use of your health spa or spa and immediately you realize something is wrong. Either water is cold, making for any under enjoyable soak or free is working whatsoever. The health spa seems dead.
For those who have an electronic system inside your health spa or spa having a digital upper control, you initially consider the upper control display to ascertain if it will explain what's going on. Searching at the upper control, the thing is abbreviations like SN1 or FLO or perhaps "----". Exactly what do these symbols and abbreviations mean?
The symbols and abbreviations shown on your spas upper control are known as error codes. They tell you just how the health spa has detected a scenario that after that it attempts to identify. Different equipment producers use different codes to recognize certain conditions discovered by the health spa self diagnostic system.
We'll consider the two health spa systems I receive most questions regarding. Balboa controls and Sundance Spas controls.
Balboa, probably the most common health spa controls producers, uses the next codes.
pd = Energy supply, unit running on battery backup
OH = Sensors reading through 112-118 Levels
Flo = Improper flow or pressure switch malfunction
Awesome = Water temp 20 levels below set point
ICE = Potential freeze condition continues to be detected
Sn1 = Hi-limit sensor malfunction
Sn3 = Temp sensor malfunction
LOC = Interlock failure - possible pump or ozone spike
(----) = Unknown temperature of water. (Shows when Health spa is first powered up after refill).
Sundance Health spa, among the biggest health spa producers, uses the next error codes.
ILOC = Interlock failure - possible pump or ozone spike
FLO = Pressure switch malfunction or Flow switch malfunction (system specific).
Hold = Flow Switch (heater is deactivated. Pump can also be deactivated).
Hold = Panel buttons pressed to a lot of occasions to rapidly.
HOT = PCB temperature above acceptable limit - air blower on.
ICE = Potential freeze condition.
PnL = Communication between your panel and circuit board is faulty.
(----) = "WATCHDOG" (health spa is deactivated) An issue continues to be detected. (system cannot identify)
Sn1 = OPEN SENSOR (heater is deactivated) or SHORTED SENSOR (health spa is deactivated).
Sn3 = OPEN SENSOR OR SHORTED SENSOR ( heater disabled).
(This isn't an entire list as well as your health spa error codes can vary based on year and model.)
Spot the commonalities and variations within the codes. Both use FLO,SN1,SN3 and ICE and so on, Variations include, (----). Meaning completely different things backward and forward systems. You have to make use of the error codes for the control system to precisely identify the issue together with your health spa.
Allows have a quick consider the FLO error code. Both producers condition FLO is triggered whenever a pressure switch malfunctions or perhaps a flow switch malfunctions. This could be in lots of situations, however, it is indeed my experience that the main reason for a health spa exhibiting the mistake code "FLO" is because of a dirty or worn-out filter.
(Some producers make an effort to limit the FLO error with various shows from the code, i.e., a good FLO or perhaps a flashing FLO (FLO error blinks on / off).
Blinking FLO = Heater continues to be deactivated, pump is on and Flow / Pressure switch are open. (What this means is the machine picks up the health spa has known as for warmth, laptop computer board has applied energy towards the pump, however it hasn't detected waterflow and drainage. It deactivates the heater to prevent harm to the heater).
Solid FLO = Pump is off, flow or pressure switch is closed. (Meaning, the machine shouldn't be discovering waterflow and drainage since the PC Board hasn't applied energy towards the pump, however the flow pressure switch says there's waterflow and drainage. The flow or pressure switch is stuck within the closed position or shorted.)
A dirty or worn-out filter may cause several error codes to become displayed. "OH" (over warmth) because water isn't moving rapidly enough with the heater vessel and also the high limit picks up hot water temperature. "FLO" since the filter won't allow enough water with the heater vessel to activate the flow or pressure switch. Filters ought to be changed roughly yearly or bi-yearly if you are using two different filters. Filters ought to be washed completely each month, and washed correctly every 3 several weeks approximately.
For additional info on error codes for the health spa, visit Health spa Parts Supply or speak to your health spa manufacturer for a listing of codes that have to do with your health spa. Much more doubt, call a health spa service specialist for troubleshooting help and repair.
No comments:
Post a Comment